Stock 1

10/2 NMD90 · Loomex Residential Building Wire · 150M Reel

SKU: WI-10/2NMD90O-150

10 AWG 2-conductor NMD90 Loomex cable with bare ground for indoor exposed work in dry locations or concealed work in dry or damp locations. Supplied in a 150 m spool, this cable is commonly used for heavier residential branch circuits; actual conductor sizing and circuit loading must follow local electrical code.

What this product is for

This 10/2 NMD90 Loomex cable is used for indoor branch circuit wiring where a 10 AWG copper cable with two insulated conductors and a bare bonding conductor is required. It is intended for exposed work in dry locations or concealed work in dry or damp locations.

Use for

Use for indoor residential and light commercial wiring, including branch circuits, feeders to fixed loads where permitted, and renovation or new construction work that calls for 10 AWG copper NMD90 cable. The 150 m spool suits longer pulls and multi-room rough-in work.

Avoid for

Avoid using this cable in wet locations, direct burial, outdoor exposed runs, or where armoured or conduit wiring methods are required. Do not use where a different conductor count, voltage rating, or cable type is specified.

Best for

Best for electricians and contractors who need Canadian NMD90 Loomex for indoor rough-in with a practical 150 m spool length. It is a typical choice when moving beyond 15 A and 20 A branch circuit cable sizes into heavier 10 AWG applications.

Installed in

Installed in wood-frame walls, ceilings, floor cavities, and other indoor concealed spaces in dry or damp building areas, or exposed in dry locations where code permits. Approximate outside diameter is 0.481 in (12.2 mm), which can help with box fill and routing planning.

Why this product exists

NMD90 provides a common Canadian non-metallic sheathed wiring method for indoor copper branch circuit installation. The 90 deg C conductor insulation supports modern installation requirements, while final ampacity and termination limits still depend on equipment ratings and code rules.

Compared with similar products

Compared with 14/2 or 12/2 NMD90, this 10/2 cable is larger and typically selected for higher-load branch circuits where 10 AWG copper is specified. Compared with AC90, it is lighter and faster to install in suitable indoor framed construction, but it does not provide the mechanical protection of armoured cable. Typical circuit guidance only: 30 A circuits commonly use 10 AWG copper, but actual application depends on load, termination temperature ratings, installation conditions, and local electrical code.

Specifications

Cable type: NMD90 Loomex building wire
Conductor size: 10 AWG
Conductors: 2 insulated conductors with bare ground
Conductor material: Copper
Construction: Solid
Length: 150 m (approximately 492 ft)
Voltage rating: 300 V
Temperature rating: -25 to 90 deg C
Insulation: PVC/Nylon
Outer jacket: PVC
Approximate outside diameter: 0.481 in (12.2 mm)
Typical jacket colour shown by distributor listing: Red
Application: Exposed work in dry locations or concealed work in dry or damp locations
Standards: CSA C22.2 No. 48, Canadian Electrical Code

Estimated trade guidance is provided for buying context only. Actual performance depends on installation conditions, termination ratings, bundling, ambient temperature, and local electrical code.

- SKU
  WI-10/2NMD90O-150
- Manufacturer Part #
  10/2NMD90O-150
Application
Exposed work in dry locations or concealed work in dry or damp locations
Voltage
300 V
Conductor Size
10 AWG
Temperature Rating
-25 to 90 deg C
Conductor Material
Copper
Cable Type
NMD90 Loomex building wire
Conductors
2 insulated conductors with bare ground
Construction
Solid
Length
150 m (approximately 492 ft)
Standards
CSA C22.2 No. 48, Canadian Electrical Code
Insulation
PVC/Nylon
Approximate Outside Diameter
0.481 in (12.2 mm)
Outer Jacket
PVC
Brands
White Label
Stock in Flesherton
1

Aptico Supply Delivery

Fast Electrical Supply Delivery Across Ontario

Local delivery routes, pickup options, and contractor-focused service from our Elmira and Flesherton locations.

Shop Products Ask About Delivery

Real-Time Inventory

Contractor Delivery Routes

Elmira & Flesherton Pickup

Local Ontario Service

Delivery Built Around Electrical Contractors

Aptico Supply helps electricians, contractors, and commercial buyers get the electrical materials they need without unnecessary delays. Whether you are ordering for a jobsite, restocking service inventory, or arranging pickup, our delivery options are designed to keep work moving.

Free Daily Delivery

Free daily delivery is available for larger contractor accounts.

Order by 9:00 AM for morning delivery
Order by 2:00 PM for afternoon delivery
Available in qualifying local delivery areas

Free Weekly Delivery

Free weekly delivery is available for smaller accounts in select service areas.

Elmira area delivery: Tuesday
Flesherton area delivery: Thursday
Order by 11:00 AM on the route day

Pickup Options

Pickup is available from our Ontario locations for customers who prefer to collect their order directly.

Elmira pickup available
Flesherton pickup available
Call ahead for large or special-order items

Local Delivery Areas

See our local delivery coverage below. Delivery charges may apply outside regular route areas or for oversized items.

Delivery Questions

Do you offer free delivery?

Yes, free delivery is available for qualifying contractor accounts and selected local delivery routes.

Can I pick up my order?

Yes, pickup is available from our Elmira and Flesherton locations.

Do delivery charges apply?

Delivery charges may apply outside regular local routes, for smaller orders, or for oversized and heavy items.

Can you deliver to jobsites?

Yes, jobsite delivery may be available depending on the order size, location, and delivery schedule.

Need Electrical Supplies Delivered?

Contact Aptico Supply to confirm your delivery options, pickup availability, or contractor account eligibility.

Contact Aptico Supply

We accept the following payment methods:

Accepted payment methods

To replace this text with your store's actual info on payment methods, go to "Design -> Menus & Pages -> Product Page Tabs" and edit the Payment methods page.

This page is intended for your policy regarding returns and refunds.

Here you can provide information as to what products can be returned, how many days your customers have to return their purchase, whether they will receive a refund in the original form of payment, a replacement or a store credit, who pays for the shipping of the previously purchased products to the store, and so on.

To replace this text with your store's actual return policy, go to "Design -> Menus & Pages -> Product Page Tabs" and edit the Return Policy page.